I'm trying to setup a background job in a QNAP TVS-871T. It doesn't come with nohup pre-installed. I've found multiple references to install it on a QNAP device (e.g. So let’s install ipkg so we can then install other software on the Synology DiskStation! Start by finding out which CPU your Synology DiskStation uses. Now find out which ipkg bootstrap you should get at this page, located on the Synology wiki: Overview on modifying the Synology Server, bootstrap, ipkg etc 2. I would like to run redmine on my NSlu2 NAS Server (QNAP) with an arm processor. I installed ipkg and so on everything runs well. Trying to install redmine I need to install ruby-on-rails. The problem is that the my repositories install ruby version 1.9.1 which is too new for redmine and is not going to work. ) but that doesn't seem to apply to this device; there is no such package available in the web interface. Seems to be a variant of an Ubuntu distro but none of its package managers are available. Cat /proc/version Linux version 3.12.6 (root@NasX86Builder) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Wed Jun 1 06:14:19 CST 2016 It's running QTS 4.2 if that makes any difference. Does the package manager not provide coreutils/nohup? First you need to install ipkg - In the device's Administration interface, select the 'System Tools' -> 'QPKG' page, click on 'Get QPKG' button. Once done login to your server via SSH and 'ipkg install sed' you can basically use this to install most packages that for linux. In the absence of package management, you would have to install a binary. • If you're lucky, you could figure out what Ubuntu/Debian version is most compatible with your OS and install the nohup binary by copying it into your path (/usr/bin/nohup on Ubuntu 16.04). • If you have no such luck getting it to run due to some shared library dependency issue or whatever, you could build a binary for your QNAP that is statically linked so that it has no shared library dependencies. On Debian/Ubuntu it's in the coreutils package. Chances are you'll get it working - it may have little or no dependencies. Try the above steps and if they don't work post the details in your question and we'll try again. 日本語のページは をご覧ください。 / Click for Japanese version. Recently I installed Minidlna ver.1.0.25 on my QNAP NAS TS-419P II (firmware 3.8.1 Build 20121205) from the source, so here is what I did. Caution: This article is NOT meant to be a step-by-step guide; You need basic knowledge of Linux, building open-source project, and your QNAP NAS system. Also, please be noted that some part of this article are environment-specific. (For example, I use '/share/MD0_DATA/' to point out my RAID HDD volume on my NAS.) What is Minidlna?Minidlna is an open-source UPnP-AV media server developed for ReadyNAS, a Netgear product. Official project page is here:. Rogue trooper game wiki. Rogue, apparently the sole living G.I. This is often referred to as the Quartz Zone Massacre. (until he meets Venus Bluegenes), goes AWOL so as to trace down the Traitor General accountable and penalize the remainder of the G.I.s. All of the G.I.s were created resistant to all toxins, diseases, and acids (except for one). The current of air supreme headquarters deploy their secret weapon in associate degree mobile assault, however a traitor has betrayed the key of the G.I.s to the Norts and that they area unit massacred throughout the drop. The description of the project says: 'if you are looking for a NAS, please consider ReadyNAS first!' So, you should first consider buying a ReadyNAS, instead of installing Minidlna server on a QNAP NAS:-) For building/installing Minidlna, you can find some useful information on the QNAP forum:. Install Optware IPKGOptware IPKG can be installed from the Web Interface. Just clicked 'Install'. Then I logged on to my NAS via SSH and ran 'ipkg update'. Indramat drive top software manual. Retrieve the source codeI've used version 1.0.25 (stable release). Downloaded minidlna_1.0.25_src.tar.gz from the project page (), copied it onto my QNAP, and extract it there. Prepare the librariesThe file INSTALL says: Prerequisites: - libexif - libjpeg - libid3tag - libFLAC - libvorbis - sqlite3 - libavformat (the ffmpeg libraries) - libuuidSo I installed them using IPKG. From the SSH console, I ran: # ipkg install libexif # ipkg install libjpeg # ipkg install libid3tag # ipkg install flac # ipkg install libvorbis # ipkg install sqlite # ipkg install ffmpeg. Note: The package 'sqlite' provides sqlite version 3, while the package 'sqlite2' provides version 2. You can run 'ipkg info sqlite' and 'ipkg info sqlite2' to verify the versions. I have NOT installed libuuid since it was already on my QNAP system. I also installed 'gcc' and 'make' packages since these are needed to build the project. # ipkg install gcc make 4. Modify Makefile and genconfig.shMinidlna project assumes that the header files are located under /usr/include. However, since I'm using Optware, these files are placed under /opt/include. So I have replaced all of '/usr/include' with '/opt/include' in Makefile and genconfig.sh. Also, I added an extra line in the Makefile: LDFLAGS += -L/opt/lib -Wl,-rpath,/opt/lib This is because the library files are located under /opt/lib. Usb controller walmart. Without this, the build succeeded, but I got an error message like: minidlna: error while loading shared libraries: libexif.so.12: cannot open shared object file: No such file or directory when I ran the server.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |